|Radial load rating||++|
|Axial load rating||+|
|Suitable to servomotor applications||YES|
|Number of sizes in this line||3 (60 to 120)|
|Standard Angular backlash||≤5 or 8 arc-min|
|Optional reduced backlash||≤3 or 5 arc-min|
|Available ratios||3 to 100|
|Motor shaft connection||Balanced coupling|
The planet carrier is a "cage" (monobloc part holding the gears from both sides), providing stiffness and acceleration capacity to the gearbox.
The planet carrier is monobloc with the output shaft too.
This cage is centered into the inner planetary ring by means of 2 radial ball-bearings. This construction reinforces the acceleration capacity because the tilt of the shaft is limited, and the gearbox is able to accept significant torque variations.
The motor shaft connection is a balanced coupling, so the efforts on your motor bearings are minimal.
Installation is fast and easy thanks to a 1-screw lock to your motor shaft.
The gearbox will be delivered with the adapting flange corresponding to your motor.
The Wiser SQ series follows the Perfect PitchTM concept, including the use of helical gears to provide a silent and safe operation to your system. Refer to the PerfectPitch conceptTM section for more detailed information.
LOW TO MODERATE ACCELERATION CAPACITY
The planet carrier is a single-block "cage" that was designed to increase torsional stiffness in comparison with a cantilever-type planet carrier. The planets are firmly held from both sides in order to maximize their life in high torque conditions. This planet carrier is strongly supported by 2 radial ball-bearings, to ensure perfect alignment of the planet gears, even at maximum torque. This design is adapted to stable torque or moderate acceleration.
High-precision planet gears in carburized and quenched steel allow high torque density and strong accelerations, year after year, without loss of precision.
They are supported by large, carburized, full-complement needles (needle bearings without cages), in order to maximize torque capacity and lifetime.
MORE SAFETY FOR YOUR MOTOR SHAFT
The Wiser range features a standard, balanced coupling, to make sure vibrations are not transmitted to your motor bearings.
T2n (Nm) (1)
Tmax (Nm) (2)
|Emergency stop torque (3)||1,5*Tmax|
|Max angular backlash (minutes)||1 stage||Standard : ≤5；Option : ≤3|
|2 stages||Standard : ≤8；Option : ≤5|
|Nominal input speed (rpm) (4)||4,000||3,100||2,800|
|Max input speed (rpm) (5)||7,500||6,000||5,500|
|Max radial load (N) (6)||1,100||2,200||3,600|
|Max axial load (N)||900||1,950||3,000|
|Efficiency (%) (7)||1 stage||＞97|
|Torsional stiffness (Nm/min)||6||13||24|
|Life (h) (8)||20,000|
|Min / max temperature (°C)||-15 / +45|
|Max temperature of the body (°C)||90|
|Protection class||IP 54|
|Noise level (dB) (9)||<66||<67||<71|
|Lubrication||Lifetime lubrication (Grease)|
|Color||Capri blue (RAL 5019)|
|Input flange||Anodized aluminum|
Note : Torque ratings fluctuate with the radial and axial loads that are applied on the shaft. Consult us to know the rated / acceleration / emergency stop torque applicable in your application. Click here for more information.
Following the ISO 6336-2 standard, for a 20,000 hours life with a 1,25 application factor, at nominal speed with 60°C internal temperature. Applying a lower torque prolounges life significantly.
Following ISO 6336-2 standard, for 2,000h (10% of life) with a 1,4 safety factor, at nominal speed with 60°C internal temperature. Using a torque higher than the nominal torque wears the internal gears.
1,000 occurences maximum
Speed at which nominal torque can be applied for 20,000 hours
Acceptable for a short duration only
Applied at the middle of the output shaft with a 100 rpm speed.
Measured with a 60°C gearbox using nominal speed and torque. Refer to temperature factors in dedicated section.
Minimum life at nominal speed and torque. Using lower speed and/or torque prolounges life significantly.
At nominal speed, measured at 1m.
* Other ratios are available upon request
This section proposes a selection of drawings of WISER-SQ-ST with adapting flanges corresponding to the most popular motors.
Additional drawings will be added shortly. In the meantime you are invited to click here to request datasheets and 3D drawings.
|Gearbox model||Number of stages||Input||Shaft||
|Wiser-SQ-ST-060||1 stage - ratios 3 to 10||Standard||Keyed||JVL||MIS232T|
|Wiser-SQ-ST-060||1 stage - ratios 3 to 10||Standard||Keyed||KEBA||DMS2-058-0012660|
|Wiser-SQ-ST-060||2 stages - ratios 12 to 100||Standard||Keyed||MITSUBISHI||HG-KR23|
|Wiser-SQ-ST-060||2 stages - ratios 12 to 100||Standard||Keyed||MITSUBISHI||HG-KR43B|
|Wiser-SQ-ST-090||1 stage - ratios 3 to 10||Standard||Keyed||FUJI||GYS401DC2-T2A|
|Wiser-SQ-ST-090||1 stage - ratios 3 to 10||Standard||Keyed||SIEMENS||1FT5046|
|Wiser-SQ-ST-090||2 stages - ratios 12 to 100||Compact||Keyed||KOLLMORGEN||AKM2G2|
|Wiser-SQ-ST-120||1 stage - ratios 3 to 10||Standard||Keyed||OMRON||R88M-K1K020|
|Wiser-SQ-ST-120||2 stages - ratios 12 to 100||Compact||Smooth||SIEMENS||1FK7042|
International machine-tool exhibition. Meet our team on stand 6 / D-14
Meet with our Italian team! New Reckon products will be displayed on HALL 3 STAND D051
Access was developped to offer the lowest price on the market of low-backlash planetary gearboxes. Yet it features carburized and ground planets, a 5 to 8 arc-minutes backlash and a monobloc housing for unrivaled stiffness amongst competition products!